Installation Instruction

Place the panels in position exactly so that the tongue is immediately adjacent to the groove. Ensure that both panels are lying at the same level along their entire length.

The special form of the spring flanks will expand the opening of the groove a little when the panels are pushed together.

Once the spring has clicked into position in the groove the panels are joined together by the SNAP connection. The precision mashiningguarantees a perfect possible fitting.

Installation Instruction:

• IMPORTANT:
  If installing in rooms used for commercial purposes, i.e. starting from Utilisation Category 31, the groove and tongue joint must be glued. In the case of floor areas subject to heavy wear, and also in rooms in which considerable fluctuations in climatic conditions are to be expected (ideal room climate: 20-22°C, 50- 60% relative humidity) we recommend that you glue all the panels. For this purpose you should apply a thin continuous bead of glue to the topside of the tongue.
  Use K-Floor Glue or an equivalent D3 glue.

• In order to carry out the installation work you will need:
  0.2 mm thick polyethylene film, footstep sound insulation, K-Floor Glue or an equivalent D3 glue, spacers, push block, pull-iron, saw, hammer (min. 500 g) pencil, and straight edge. Please make a point of using only the Kaindl accessories because these have been designed specially for working with Snap by Kaindl. Once a package has been opened its contents of a pack should be used without delay.

• Snap by Kaindl is installed floating - the tongue and the groove are mechanically locked together by the Snap Profile! Under no circumstances may panels be glued, nailed, or otherwise fixed (e.g. door stopper) to the underfloor.

• Wood needs room to expand. A space of 10-15 mm should always be left between the panels and the walls or any other fixed elements (such as heating pipes or doorframes). Installation should be carried out at a room temperature of at least 18°C and a floor temperature of 15°C. The relative humidity should be < 70%. The temperature difference between the panels and the substrate should not exceed ±3°C.

• The sub-floor must be absolutely level, dry, clean, and firm (old fixed carpet must be removed). Differences in floor level of more than 3 mm must either be sanded down or filled in with filling compound.

• For damp insulation (cement, tiles, etc.) first lay a polyethylene film (0.2 mm in thickness). The seams of the foil should overlap by at least 20 cm and must be taped.

• For footstep sound insulation use a special underlay such as Kaindl Protection Matting. The seams should be laid in the same direction as the panels.

• The Snap by Kaindl panels should preferably be installed longitudinally to th main light source.

• For installation on underfloor heating please comply with the special instructions. You can obtain these from your Snap by Kaindl dealer.

• Expansion joints (at least 2 cm in width) must be fitted between adjoining rooms and also in rooms measuring more than 10 metres in the direction of the panel length and more than 8 metres in the direction of the panel width. Please comply exactly with the installation instructions. No complaints can be accepted in cases of faulty installation.

• Please carefully adhere to the installation instructions. The installer is liable for inappropriate use.

Installation:

• Lay the first Snap by Kaindl panel with the groove towards the wall.

• Check the distance to the wall (of at least 10- 15 mm) with a spacer and set straight. In the case of rooms having a length greater than 7 metres you should allow a special distance from the wall of 1.4 mm per for each metre of room length at both sides of the room.

• For accurate cutting of the last panel in the row, rotate this through 180° and, with the pattern side upwards, place beside the already installed row (tongue-to-tongue).

• Allow for distance from wall at end of panel. Mark out offcut and saw off.

• Always saw from the upper surface of the panel (to avoid splintering the edges) - only when using an electric jig saw or a hand-held circular saw should the patterned side be placed facing downwards.

If the wall is not straight:

• Place panels straight then use a spacer or similar instrument to mark the actual line of the wall on the first row of panels.

• Saw the panels longitudinally according to the marking.

• Also, the first row of panels must be cut longitudinally if the final row of panels is going to be narrower than 5 cm. 

• Start each new row with the left-over piece from the preceding row. The transverse joints must be offset by at least 40 cm.

• Please take particular care to ensure that the first three rows are perfectly straight.

• Carefully fit the panels together with the aid of the hammer and the push block. Start by interlocking the flat-lying longitudinal edge. Begin with a panel corner, taking care to ensure the correct elevation of the panels. Only then fit together the transverse joints. However, before fitting the panels you should bring them as near to their final position on the floor as possible.

• Those sections of the floor which will be subjected to heavy domestic wear may also be glued if you so wish. In such cases, apply a thin continuous thread of glue to the top side of the tongue. For this purpose you should use a D3 glue which is suitable for laminate flooring applications.

• Fit the last panel in the row with the aid of the pull-iron.

• Apply only as much force as is absolutely necessary. Once the first three rows have been interlocked, move them into the final position and fix them next to the walls with spacers so that they cannot move.

Where there are heating pipes or room dividers:

• Position the panel row so that a transverse joint coincides with the pipe.
  First cut the panel to the correct length.

• Then lay the panel section beside the actual position, measure the recesses with a ruler and draw in. 

• Now drill out the marked sections.

• Remember the necessary distance (10–15mm) on each sides. 

• Join up the sawn off piece again tightly behind the heating pipe (using the spacer).

When a doorframe has to be shortened:

• Lay a panel next to the frame (with the pattern side facing downwards) 

• Cut into the doorframe with the straight back saw

• Then slide the panel under the frame with the pattern side upwards.

• Don't forget to allow for freedom of movement here, too.

To finish off:

• Measure the exact width of the last panel row. 

• To do this lay a panel on the previous panel row. 

• Then lay a second panel on the panel to be measured with the tongue to the wall and
  use as a straight edge and saw the panel along the marking.

• And please not forget the wall spacing!

• Fit the last panel carefully using the pull-iron. Finished !

Your Snap by Kaindl floor can be walked on and furnished immediately.
There is no need to move the furniture out of the room when installing the flooring.
As soon as part of the flooring has been installed the furniture can be moved onto that part.

Cleaning:

• Simply clean Snap by Kaindl with a soft broom or a vacuum cleaner.

• Wipe off footmarks and clinging dirt with a wrung-out moist cloth. Do not use wet cloths.

• Do not attempt to clean Snap by Kaindl with wax, polish, or scouring materials.

• Stubborn stains can be removed with special stain remover.

• For regular cleaning and maintenance we recom-mend Kaindl Laminate Cleaner.

Care:

• Lay dirt-absorbing mats in areas of high dirt incidence (such as entrance halls and hallways).

• Fit felt tips to the feet of your furniture and fit soft rubber casters to mobile furniture.

• The ideal indoor climate is 20-22°C, 50-60% relative humidity.
  Extreme fluctuations in the indoor climate may cause slight deformation of the panels and
  the formation of minor joints in the floor.

© Kaindl Flooring, www.kaindl.com.hk